{"id":3649,"date":"2026-11-17T16:48:29","date_gmt":"2026-11-17T16:48:29","guid":{"rendered":"https:\/\/modernhvactech.com\/?p=3649"},"modified":"2026-11-17T16:48:29","modified_gmt":"2026-11-17T16:48:29","slug":"furnace-ignitor-replacement-signs-testing-and-diy","status":"publish","type":"post","link":"https:\/\/modernhvactech.com\/es\/blog\/furnace-ignitor-replacement-signs-testing-and-diy\/","title":{"rendered":"Sustituci\u00f3n del encendedor del horno: se\u00f1ales, pruebas y c\u00f3mo hacerlo usted mismo."},"content":{"rendered":"<div class=\"vc_row wpb_row row top-row\"><div class=\"vc_column_container col-md-12\"><div class=\"wpb_wrapper vc_column-inner\"><h1 style=\"font-family:Abril Fatface;font-weight:400;font-style:normal\" class=\"vc_custom_heading align-left\" >Furnace Ignitor Replacement<\/h1>\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\">The fastest route to furnace ignitor replacement is to confirm the ignitor is the failed part, buy an exact-match replacement, shut off power and gas, swap the part without touching the element, and test a full heating cycle. If gas lines and 120-volt wiring make you uneasy, hand the job to a technician.<\/p>\n\n\t\t<\/div>\n\t<\/div>\n\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\">A bad ignitor is easy to blame wrongly. The furnace starts up and then nothing warms the house. However, a weak flame sensor, a gas valve or a control board produces the same symptoms, so the diagnosis matters more than the part. Guess wrong and you pay for a replacement you did not need.<\/p>\n<h2><!-- \/wp:post-content --><\/h2>\n<p><!-- wp:paragraph \/--><\/p>\n<h2><!-- wp:shortcode --><\/h2>\n\n\t\t<\/div>\n\t<\/div>\n\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\">This guide walks through furnace ignitor replacement in order: why ignitors fail and when to replace one, how to confirm the diagnosis, how to choose the right part, and how to install it.<\/p>\n<h2><!-- \/wp:shortcode --><\/h2>\n<p><!-- wp:paragraph \/--><\/p>\n<h2><!-- wp:shortcode --><\/h2>\n\n\t\t<\/div>\n\t<\/div>\n\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\">Modern HVAC Tech has <a href=\"https:\/\/modernhvactech.com\/es\/furnace-repair-in-chicago\/\" target=\"_blank\" rel=\"noopener noreferrer nofollow\"><u>repaired furnaces in Chicago<\/u><\/a> and the north suburbs for more than twenty years, so the checks below come from real service calls.<\/p>\n<h2><!-- \/wp:shortcode --><\/h2>\n<p><!-- wp:paragraph \/--><\/p>\n<h2><!-- wp:shortcode --><\/h2>\n\n\t\t<\/div>\n\t<\/div>\n\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t\n\t\t<\/div>\n\t<\/div>\n<h2 style=\"font-family:Abril Fatface;font-weight:400;font-style:normal\" class=\"vc_custom_heading align-left\" >Why ignitors fail and when to replace one<\/h2>\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\">Replace a furnace ignitor when it no longer glows, shows cracks, or the furnace fails to light on repeated tries. A working ignitor does not need replacing on a schedule, but it is a wear item that typically lasts 3 to 7 years.<\/p>\n<h2><!-- \/wp:shortcode --><\/h2>\n<p><!-- wp:paragraph \/--><\/p>\n<h2><!-- wp:shortcode --><\/h2>\n\n\t\t<\/div>\n\t<\/div>\n<h3 style=\"font-family:Abril Fatface;font-weight:400;font-style:normal\" class=\"vc_custom_heading align-left\" >What the ignitor does<\/h3>\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\"><span class=\"citation-4576 citation-4577 citation-end-4577\">Most modern gas furnaces use a hot surface ignitor made of silicon carbide or silicon nitride, and you may also see it spelled igniter. When the thermostat calls for heat, current heats the element to well over 2,000\u00b0F until it glows orang<\/span>e. Afterward, the gas valve opens so fuel flows over the hot tip. Without that crucial glow, the control board shuts the sequence down for safety.<\/p>\n<h2><!-- \/wp:shortcode --><\/h2>\n<p><!-- wp:paragraph \/--><\/p>\n<h2><!-- wp:shortcode --><\/h2>\n\n\t\t<\/div>\n\t<\/div>\n\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p><!-- \/wp:shortcode --><br \/><!-- wp:image {\"id\":3641,\"align\":\"center\",\"className\":\"wp-image-3641 size-full\"} --><\/p>\n<figure class=\"wp-block-image aligncenter wp-image-3641 size-full\"><img loading=\"lazy\" decoding=\"async\" class=\"aligncenter wp-image-3651 size-full\" title=\"Ignitor\" src=\"https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/Ignitor.png\" alt=\"Ignitor\" width=\"1919\" height=\"994\" srcset=\"https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/Ignitor.png 1919w, https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/Ignitor-1024x530.png 1024w, https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/Ignitor-768x398.png 768w, https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/Ignitor-1536x796.png 1536w, https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/Ignitor-640x332.png 640w, https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/Ignitor-400x207.png 400w, https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/Ignitor-367x190.png 367w\" sizes=\"auto, (max-width: 1919px) 100vw, 1919px\" \/><figcaption class=\"wp-element-caption\">\u00a0<\/figcaption><\/figure>\n<p><!-- \/wp:image --><br \/><!-- wp:paragraph -->\u00a0<\/p>\n\n\t\t<\/div>\n\t<\/div>\n<h3 style=\"font-family:Abril Fatface;font-weight:400;font-style:normal\" class=\"vc_custom_heading align-left\" >Signs it is failing<\/h3>\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 3 &#091;&#093;\">A dying ignitor rarely quits without warning. Watch for these:<\/p>\n<ul>\n<li>Furnace clicks or the blower runs, but <strong>no heat arrives<\/strong>.<\/li>\n<li>You see <strong>no orange glow<\/strong> through the viewing port during startup.<\/li>\n<li>Lights only on some attempts, or <strong>short cycles<\/strong> by starting and stopping repeatedly.<\/li>\n<li>Element has <strong>hairline cracks<\/strong>, white marks, or black spots.<\/li>\n<\/ul>\n<h2><!-- \/wp:paragraph --><\/h2>\n<p><!-- wp:paragraph \/--><\/p>\n<h2><!-- wp:shortcode --><\/h2>\n\n\t\t<\/div>\n\t<\/div>\n\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\">The intermittent case is the one people miss. A weak ignitor may light the furnace half the time for weeks before it fails completely, so a furnace that needs a second or third try deserves attention now.<\/p>\n<h2><!-- \/wp:shortcode --><\/h2>\n<p><!-- wp:paragraph \/--><\/p>\n<h2><!-- wp:shortcode --><\/h2>\n\n\t\t<\/div>\n\t<\/div>\n<h3 style=\"font-family:Abril Fatface;font-weight:400;font-style:normal\" class=\"vc_custom_heading align-left\" >How long it lasts and what shortens it<\/h3>\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\">Published figures run from 3 to 5 years up to 3 to 7 years, so treat any single number as a range. Dust, a clogged filter, frequent cycling, power surges and skin oils from handling all cut that life. Chicago&#8217;s long heating season adds cycles, and as a result ignitors here tend to age toward the short end.<\/p>\n\n\t\t<\/div>\n\t<\/div>\n\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 2 &#091;&#093;\">That said, a healthy ignitor does not need replacing on a calendar. But if the furnace is past the 5-year mark and a technician already has the panel open, swapping a visibly worn ignitor saves a second visit.<\/p>\n<blockquote>\n<p>Replace the ignitor when it fails to glow, cracks, or lights the furnace unreliably, not on a fixed date.<\/p>\n<\/blockquote>\n\n\t\t<\/div>\n\t<\/div>\n<h2 style=\"font-family:Abril Fatface;font-weight:400;font-style:normal\" class=\"vc_custom_heading align-left\" >Step 1. Confirm the ignitor is the problem<\/h2>\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\">Confirm the fault by watching one full startup cycle, then testing the ignitor with a multimeter. Replace it only if it fails to glow or reads outside its rated resistance.<\/p>\n\n\t\t<\/div>\n\t<\/div>\n<h3 style=\"font-family:Abril Fatface;font-weight:400;font-style:normal\" class=\"vc_custom_heading align-left\" >Watch the startup sequence<\/h3>\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\">Set the thermostat well above room temperature. Use the viewing port if your furnace has one, rather than running the furnace with the panel off. The sequence runs like this: the inducer fan starts, the ignitor glows, the gas valve opens, and the burners light. Next, match what you see to the likely culprit:<\/p>\n\n\t\t<\/div>\n\t<\/div>\n\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\"><img loading=\"lazy\" decoding=\"async\" class=\"aligncenter wp-image-3652 size-large\" title=\"ignitor start \" src=\"https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/Screenshot-37-1024x588.png\" alt=\"ignitor start \" width=\"1024\" height=\"588\" srcset=\"https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/Screenshot-37-1024x588.png 1024w, https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/Screenshot-37-768x441.png 768w, https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/Screenshot-37-640x368.png 640w, https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/Screenshot-37-400x230.png 400w, https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/Screenshot-37-367x211.png 367w\" sizes=\"auto, (max-width: 1024px) 100vw, 1024px\" \/><\/p>\n\n\t\t<\/div>\n\t<\/div>\n\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<table>\n<tbody>\n<tr>\n<td><strong>What you see<\/strong><\/td>\n<td><strong>Likely cause<\/strong><\/td>\n<\/tr>\n<tr>\n<td>Nothing starts, not even the fan<\/td>\n<td>Thermostat, power, door switch, or control board<\/td>\n<\/tr>\n<tr>\n<td>Fan runs, no glow<\/td>\n<td>Dead ignitor, or no power reaching it<\/td>\n<\/tr>\n<tr>\n<td>Ignitor glows, no flame<\/td>\n<td>Gas supply or gas valve<\/td>\n<\/tr>\n<tr>\n<td>Flame lights, then dies within seconds<\/td>\n<td>Dirty flame sensor<\/td>\n<\/tr>\n<tr>\n<td>Dim glow, or lights only sometimes<\/td>\n<td>Aging ignitor<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n\n\t\t<\/div>\n\t<\/div>\n\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\">Also <a href=\"https:\/\/modernhvactech.com\/es\/blog\/how-often-to-change-your-furnace-filter-in-chicago-a-complete-guide\/\" target=\"_blank\" rel=\"noopener noreferrer nofollow\">check the filter<\/a> and any LED code on the control board. Many boards flash a code for ignition failure, and the code label is usually on the inside of the door.<\/p>\n<p data-pm-slice=\"1 1 &#091;&#093;\"><img loading=\"lazy\" decoding=\"async\" class=\"aligncenter wp-image-3653 size-full\" title=\"Ignitor control\" src=\"https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/ingnitor-control.png\" alt=\"Ignitor control\" width=\"1919\" height=\"994\" srcset=\"https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/ingnitor-control.png 1919w, https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/ingnitor-control-1024x530.png 1024w, https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/ingnitor-control-768x398.png 768w, https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/ingnitor-control-1536x796.png 1536w, https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/ingnitor-control-640x332.png 640w, https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/ingnitor-control-400x207.png 400w, https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/ingnitor-control-367x190.png 367w\" sizes=\"auto, (max-width: 1919px) 100vw, 1919px\" \/><\/p>\n\n\t\t<\/div>\n\t<\/div>\n<h3 style=\"font-family:Abril Fatface;font-weight:400;font-style:normal\" class=\"vc_custom_heading align-left\" >Test it with a multimeter<\/h3>\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\">First, turn off power at the breaker and close the gas valve. Then unplug the ignitor&#8217;s wire harness and set your meter to ohms. Touch one probe to each terminal. A reading within the rated range means the element is intact, while a reading of &#8220;OL&#8221; or infinity means it is broken.<\/p>\n\n\t\t<\/div>\n\t<\/div>\n\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\">Rated resistance varies by model. One manufacturer&#8217;s silicon nitride ignitor, for example, specifies 40 to 70 ohms when new, so check your furnace manual or the ignitor&#8217;s label instead of trusting a universal number. If the ignitor tests good and the symptoms continue, stop. The fault lies elsewhere, and that is a job for a technician.<\/p>\n\n\t\t<\/div>\n\t<\/div>\n\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<blockquote>\n<blockquote data-pm-slice=\"2 1 &#091;&#093;\">\n<p>A cracked element or an &#8220;OL&#8221; reading proves the ignitor is dead; a good reading means keep looking.<\/p>\n<\/blockquote>\n<\/blockquote>\n\n\t\t<\/div>\n\t<\/div>\n<h2 style=\"font-family:Abril Fatface;font-weight:400;font-style:normal\" class=\"vc_custom_heading align-left\" >Step 2. Weigh the DIY against a pro<\/h2>\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\">Doing it yourself saves labor costs but adds risk around gas and electricity.<\/p>\n<p data-pm-slice=\"1 1 &#091;&#093;\">Because the bill is small, furnace ignitor replacement almost always passes the $5,000 rule. A rough $350 repair on a 15-year-old furnace scores $3,750, which is well under the line, so repairing beats replacing even on an older unit.<\/p>\n\n\t\t<\/div>\n\t<\/div>\n<h2 style=\"font-family:Abril Fatface;font-weight:400;font-style:normal\" class=\"vc_custom_heading align-left\" >When to hire a pro<\/h2>\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\">Call a technician if the ignitor tests good, or if you are not comfortable shutting off gas and working near 120-volt wiring. The same goes for a furnace still under warranty, since DIY work or non-OEM parts can void coverage. Meanwhile, what you pay a pro for is the diagnosis, the safe gas handling and the full-cycle test, because the part itself costs little.<\/p>\n\n\t\t<\/div>\n\t<\/div>\n\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\">Modern HVAC Tech runs <a href=\"https:\/\/modernhvactech.com\/es\/emergency-furnace-repair-in-chicago-il\/\" target=\"_blank\" rel=\"noopener noreferrer nofollow\">24\/7 emergency furnace repair<\/a> across Chicago and the north suburbs with licensed technicians and upfront pricing, so ask for the price before any work begins. If you want a weak ignitor caught before it fails, our <a href=\"https:\/\/modernhvactech.com\/es\/furnace-maintenance-in-chicago\/\" target=\"_blank\" rel=\"noopener noreferrer nofollow\">pay-per-visit maintenance<\/a> is $149 per residential unit.<\/p>\n\n\t\t<\/div>\n\t<\/div>\n<h2 style=\"font-family:Abril Fatface;font-weight:400;font-style:normal\" class=\"vc_custom_heading align-left\" >Step 3. Buy the right ignitor<\/h2>\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\">Buy the ignitor that matches your furnace&#8217;s model number, and choose an OEM part when you can. A universal ignitor is acceptable only when its connector, length, voltage, and mounting fit your furnace.<\/p>\n\n\t\t<\/div>\n\t<\/div>\n<h3 style=\"font-family:Abril Fatface;font-weight:400;font-style:normal\" class=\"vc_custom_heading align-left\" >Find your part number<\/h3>\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\">Open the furnace door and read the model number on the rating plate. Many ignitors also carry a part number stamped on the ceramic base or bracket. Search the model number plus &#8220;ignitor,&#8221; or bring the old ignitor to an HVAC supply counter. Buy before you start the repair, not in the middle of it.<\/p>\n\n\t\t<\/div>\n\t<\/div>\n<h3 style=\"font-family:Abril Fatface;font-weight:400;font-style:normal\" class=\"vc_custom_heading align-left\" >Universal or OEM<\/h3>\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 3 &#091;&#093;\">Universal ignitors cover many furnaces and are often cheaper and easier to find on short notice. OEM parts, on the other hand, are built for your exact unit, which gives the best fit and the cleanest warranty position. Before you trust a universal part, confirm all of these:<\/p>\n<ul>\n<li><strong>Voltage<\/strong> matches, typically 120V.<\/li>\n<li><strong>Connector<\/strong> plugs into your harness, or you are prepared to splice correctly.<\/li>\n<li><strong>Length and mounting bracket<\/strong> put the tip in the same spot as the old one.<\/li>\n<li><strong>Resistance<\/strong> falls in a range your furnace&#8217;s board accepts.<\/li>\n<\/ul>\n\n\t\t<\/div>\n\t<\/div>\n\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&quot;blockquote&quot;,{}&#093;\"><em>A universal ignitor works only when connector, length, voltage, and mounting all match the original.<\/em><\/p>\n\n\t\t<\/div>\n\t<\/div>\n<h2 style=\"font-family:Abril Fatface;font-weight:400;font-style:normal\" class=\"vc_custom_heading align-left\" >Step 4. Replace the ignitor and test the furnace<\/h2>\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\">To replace the ignitor, cut power and gas, let the part cool, unplug and unscrew the old one, mount the new one in the same position, and test a full cycle. Handle the element as little as possible, because skin oils can create hot spots that burn it out early.<\/p>\n\n\t\t<\/div>\n\t<\/div>\n\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<h3 data-pm-slice=\"1 3 &#091;&#093;\">Installation steps<\/h3>\n<ol>\n<li>Turn the thermostat down, switch off the furnace at the breaker, and close the gas valve.<\/li>\n<li>Wait 10 to 15 minutes. A recently used ignitor can burn you.<\/li>\n<li>Remove the access panel and find the ignitor beside the burners. Take a photo of the wiring.<\/li>\n<li>Unplug the harness, remove the mounting screw or bracket, and slide the old ignitor out gently. It is brittle.<\/li>\n<li>Compare it against the new one for shape, length, and connector.<\/li>\n<li>Hold the new ignitor by its base or bracket, never the element, and mount it in exactly the same position.<\/li>\n<li>Reconnect the harness and make sure the wires clear the burners and hot surfaces.<\/li>\n<li>Refit the panel, reopen the gas valve, restore power, and set the thermostat to call for heat.<\/li>\n<\/ol>\n\n\t\t<\/div>\n\t<\/div>\n<h3 style=\"font-family:Abril Fatface;font-weight:400;font-style:normal\" class=\"vc_custom_heading align-left\" >Test and troubleshoot<\/h3>\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\">Run one full heating cycle and watch for the same sequence shown in the startup graphic: the inducer starts, the ignitor glows, and the burners light smoothly with no delayed whoomph. If it fails to light after two attempts, shut it down and call a professional, because repeated tries can lock out the board.<\/p>\n<p>Keep a working carbon monoxide detector near the furnace and bedrooms. If you smell gas at any point, leave the house and call your gas utility or 911 from outside.<\/p>\n\n\t\t<\/div>\n\t<\/div>\n<h2 style=\"font-family:Abril Fatface;font-weight:400;font-style:normal\" class=\"vc_custom_heading align-left\" >Wrapping up your furnace ignitor replacement<\/h2>\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\">Should you decide to hand the job over, tell the technician what you saw: whether the inducer ran, whether the ignitor glowed, and any LED code on the board. That shortens the diagnosis and the bill. Alternatively, if you would rather skip the troubleshooting entirely, <a class=\"ng-star-inserted\" href=\"https:\/\/modernhvactech.com\/es\/?p=3649&amp;preview=true\" target=\"_blank\" rel=\"noopener\" data-hveid=\"0\" data-ved=\"0CAAQ_4QMahcKEwjji4OhvI2YAxUAAAAAHQAAAAAQMQ\">book a furnace repair visit with Modern HVAC Tech<\/a>.<\/p>\n\n\t\t<\/div>\n\t<\/div>\n<\/div><\/div><\/div><div class=\"vc_row wpb_row row top-row\"><div class=\"vc_column_container col-md-12\"><div class=\"wpb_wrapper vc_column-inner\">\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p data-pm-slice=\"1 1 &#091;&#093;\">Tambi\u00e9n puede encontrar la versi\u00f3n resumida en o <a href=\"https:\/\/www.pinterest.com\/Modernhvactechnology\/\" target=\"_blank\" rel=\"noopener\">Pines de Pinterest<\/a>. Read other blogs in our <a href=\"https:\/\/www.blogger.com\/blog\/posts\/8156562540818536461\" target=\"_blank\" rel=\"noopener\">Blogger<\/a> , <a href=\"https:\/\/www.reddit.com\/user\/ModernHVACTechnology\/\" target=\"_blank\" rel=\"noopener\">Reddit<\/a> y <a href=\"https:\/\/medium.com\/@modernhvactech\" target=\"_blank\" rel=\"noopener\">P\u00e1gina mediana <\/a>tambi\u00e9n.<\/p>\n\n\t\t<\/div>\n\t<\/div>\n<\/div><\/div><\/div><div class=\"vc_row wpb_row row top-row\"><div class=\"vc_column_container col-md-12\"><div class=\"wpb_wrapper vc_column-inner\">\n\t<div class=\"wpb_text_column wpb_content_element\" >\n\t\t<div class=\"wpb_wrapper\">\n\t\t\t<p><!-- \/wp:shortcode --><\/p>\n\n\t\t<\/div>\n\t<\/div>\n<div class=\"porto-toggles wpb_content_element\"><section class=\"toggle\"><label>Is a furnace ignitor the same as a pilot light?<\/label><div class=\"toggle-content\"><p>No. Older furnaces use <b data-path-to-node=\"6,0,1,0\" data-index-in-node=\"24\">a<\/b> small pilot light flame that stays lit. Most modern furnaces use an electronic ignitor that heats up only when the thermostat calls for heat, so furnace ignitor replacement applies to those newer units.<\/p>\n<\/div><\/section><section class=\"toggle\"><label>How long does a furnace ignitor replacement take?<\/label><div class=\"toggle-content\"><p><b data-path-to-node=\"6,1,1,0\" data-index-in-node=\"1\">Technicians<\/b> typically finish in 15 to 45 minutes once the right part is on hand. <b data-path-to-node=\"6,1,1,0\" data-index-in-node=\"82\">Beginners<\/b> should allow longer, since the cool-down, photos and testing take time.<\/p>\n<\/div><\/section><section class=\"toggle\"><label>Why does a new ignitor keep burning out?<\/label><div class=\"toggle-content\"><p>Touching the element during installation is the usual cause, followed by a part with the wrong voltage or fit. If a correct, untouched ignitor still fails within weeks, a technician should check the control board and the power it delivers.<\/p>\n<\/div><\/section><\/div><\/div><\/div><\/div>","protected":false},"excerpt":{"rendered":"Furnace Ignitor Replacement The fastest route to furnace ignitor replacement is to confirm the ignitor is the failed part, buy an exact-match replacement, shut off power and gas, swap the part without touching the element, and test a full heating cycle. If gas lines and 120-volt wiring make you uneasy, hand the job to a [...]","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[58],"tags":[],"class_list":["post-3649","post","type-post","status-publish","format-standard","hentry","category-blog"],"featured_image_src":{"landsacpe":false,"list":false,"medium":false,"full":false},"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v28.8 - https:\/\/yoast.com\/product\/yoast-seo-wordpress\/ -->\n<title>Furnace Ignitor Replacement: Signs, Testing, and DIY - Modern HVAC Tech<\/title>\n<meta name=\"description\" content=\"Furnace ignitor replacement guide: spot the signs, confirm the fault, compare and replace the part\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/modernhvactech.com\/es\/blog\/furnace-ignitor-replacement-signs-testing-and-diy\/\" \/>\n<meta property=\"og:locale\" content=\"es_ES\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Furnace Ignitor Replacement: Signs, Testing, and DIY - Modern HVAC Tech\" \/>\n<meta property=\"og:description\" content=\"Furnace ignitor replacement guide: spot the signs, confirm the fault, compare and replace the part\" \/>\n<meta property=\"og:url\" content=\"https:\/\/modernhvactech.com\/es\/blog\/furnace-ignitor-replacement-signs-testing-and-diy\/\" \/>\n<meta property=\"og:site_name\" content=\"Modern HVAC Tech\" \/>\n<meta property=\"article:publisher\" content=\"https:\/\/www.facebook.com\/modernhvactech\/\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-17T16:48:29+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/Ignitor.png\" \/>\n\t<meta property=\"og:image:width\" content=\"1919\" \/>\n\t<meta property=\"og:image:height\" content=\"994\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/png\" \/>\n<meta name=\"author\" content=\"admin\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Escrito por\" \/>\n\t<meta name=\"twitter:data1\" content=\"admin\" \/>\n\t<meta name=\"twitter:label2\" content=\"Tiempo de lectura\" \/>\n\t<meta name=\"twitter:data2\" content=\"8 minutos\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\\\/\\\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\\\/\\\/modernhvactech.com\\\/blog\\\/furnace-ignitor-replacement-signs-testing-and-diy\\\/#article\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/modernhvactech.com\\\/blog\\\/furnace-ignitor-replacement-signs-testing-and-diy\\\/\"},\"author\":{\"name\":\"admin\",\"@id\":\"https:\\\/\\\/modernhvactech.com\\\/#\\\/schema\\\/person\\\/06119bfaabf31ac6bb760868d84c5fc7\"},\"headline\":\"Furnace Ignitor Replacement: Signs, Testing, and DIY\",\"datePublished\":\"2026-11-17T16:48:29+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\\\/\\\/modernhvactech.com\\\/blog\\\/furnace-ignitor-replacement-signs-testing-and-diy\\\/\"},\"wordCount\":2053,\"publisher\":{\"@id\":\"https:\\\/\\\/modernhvactech.com\\\/#organization\"},\"image\":{\"@id\":\"https:\\\/\\\/modernhvactech.com\\\/blog\\\/furnace-ignitor-replacement-signs-testing-and-diy\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/modernhvactech.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/Ignitor.png\",\"articleSection\":[\"Blog\"],\"inLanguage\":\"es\"},{\"@type\":\"WebPage\",\"@id\":\"https:\\\/\\\/modernhvactech.com\\\/blog\\\/furnace-ignitor-replacement-signs-testing-and-diy\\\/\",\"url\":\"https:\\\/\\\/modernhvactech.com\\\/blog\\\/furnace-ignitor-replacement-signs-testing-and-diy\\\/\",\"name\":\"Furnace Ignitor Replacement: Signs, Testing, and DIY - Modern HVAC Tech\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/modernhvactech.com\\\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\\\/\\\/modernhvactech.com\\\/blog\\\/furnace-ignitor-replacement-signs-testing-and-diy\\\/#primaryimage\"},\"image\":{\"@id\":\"https:\\\/\\\/modernhvactech.com\\\/blog\\\/furnace-ignitor-replacement-signs-testing-and-diy\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/modernhvactech.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/Ignitor.png\",\"datePublished\":\"2026-11-17T16:48:29+00:00\",\"description\":\"Furnace ignitor replacement guide: spot the signs, confirm the fault, compare and replace the part\",\"breadcrumb\":{\"@id\":\"https:\\\/\\\/modernhvactech.com\\\/blog\\\/furnace-ignitor-replacement-signs-testing-and-diy\\\/#breadcrumb\"},\"inLanguage\":\"es\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\\\/\\\/modernhvactech.com\\\/blog\\\/furnace-ignitor-replacement-signs-testing-and-diy\\\/\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"es\",\"@id\":\"https:\\\/\\\/modernhvactech.com\\\/blog\\\/furnace-ignitor-replacement-signs-testing-and-diy\\\/#primaryimage\",\"url\":\"https:\\\/\\\/modernhvactech.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/Ignitor.png\",\"contentUrl\":\"https:\\\/\\\/modernhvactech.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/Ignitor.png\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\\\/\\\/modernhvactech.com\\\/blog\\\/furnace-ignitor-replacement-signs-testing-and-diy\\\/#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\\\/\\\/modernhvactech.com\\\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Furnace Ignitor Replacement: Signs, Testing, and DIY\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\\\/\\\/modernhvactech.com\\\/#website\",\"url\":\"https:\\\/\\\/modernhvactech.com\\\/\",\"name\":\"modernhvactech.com\",\"description\":\"HVAC Company in Chicago\",\"publisher\":{\"@id\":\"https:\\\/\\\/modernhvactech.com\\\/#organization\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\\\/\\\/modernhvactech.com\\\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"es\"},{\"@type\":\"Organization\",\"@id\":\"https:\\\/\\\/modernhvactech.com\\\/#organization\",\"name\":\"Modern HVAC Technology LLC\",\"url\":\"https:\\\/\\\/modernhvactech.com\\\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"es\",\"@id\":\"https:\\\/\\\/modernhvactech.com\\\/#\\\/schema\\\/logo\\\/image\\\/\",\"url\":\"https:\\\/\\\/modernhvactech.com\\\/wp-content\\\/uploads\\\/2023\\\/12\\\/logo-1.png\",\"contentUrl\":\"https:\\\/\\\/modernhvactech.com\\\/wp-content\\\/uploads\\\/2023\\\/12\\\/logo-1.png\",\"width\":2485,\"height\":737,\"caption\":\"Modern HVAC Technology LLC\"},\"image\":{\"@id\":\"https:\\\/\\\/modernhvactech.com\\\/#\\\/schema\\\/logo\\\/image\\\/\"},\"sameAs\":[\"https:\\\/\\\/www.facebook.com\\\/modernhvactech\\\/\",\"https:\\\/\\\/www.tiktok.com\\\/@modernhvactechnol\"]},{\"@type\":\"Person\",\"@id\":\"https:\\\/\\\/modernhvactech.com\\\/#\\\/schema\\\/person\\\/06119bfaabf31ac6bb760868d84c5fc7\",\"name\":\"admin\",\"sameAs\":[\"https:\\\/\\\/modernhvactech.com\"]}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"Furnace Ignitor Replacement: Signs, Testing, and DIY - Modern HVAC Tech","description":"Furnace ignitor replacement guide: spot the signs, confirm the fault, compare and replace the part","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/modernhvactech.com\/es\/blog\/furnace-ignitor-replacement-signs-testing-and-diy\/","og_locale":"es_ES","og_type":"article","og_title":"Furnace Ignitor Replacement: Signs, Testing, and DIY - Modern HVAC Tech","og_description":"Furnace ignitor replacement guide: spot the signs, confirm the fault, compare and replace the part","og_url":"https:\/\/modernhvactech.com\/es\/blog\/furnace-ignitor-replacement-signs-testing-and-diy\/","og_site_name":"Modern HVAC Tech","article_publisher":"https:\/\/www.facebook.com\/modernhvactech\/","article_published_time":"2026-11-17T16:48:29+00:00","og_image":[{"width":1919,"height":994,"url":"https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/Ignitor.png","type":"image\/png"}],"author":"admin","twitter_card":"summary_large_image","twitter_misc":{"Escrito por":"admin","Tiempo de lectura":"8 minutos"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/modernhvactech.com\/blog\/furnace-ignitor-replacement-signs-testing-and-diy\/#article","isPartOf":{"@id":"https:\/\/modernhvactech.com\/blog\/furnace-ignitor-replacement-signs-testing-and-diy\/"},"author":{"name":"admin","@id":"https:\/\/modernhvactech.com\/#\/schema\/person\/06119bfaabf31ac6bb760868d84c5fc7"},"headline":"Furnace Ignitor Replacement: Signs, Testing, and DIY","datePublished":"2026-11-17T16:48:29+00:00","mainEntityOfPage":{"@id":"https:\/\/modernhvactech.com\/blog\/furnace-ignitor-replacement-signs-testing-and-diy\/"},"wordCount":2053,"publisher":{"@id":"https:\/\/modernhvactech.com\/#organization"},"image":{"@id":"https:\/\/modernhvactech.com\/blog\/furnace-ignitor-replacement-signs-testing-and-diy\/#primaryimage"},"thumbnailUrl":"https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/Ignitor.png","articleSection":["Blog"],"inLanguage":"es"},{"@type":"WebPage","@id":"https:\/\/modernhvactech.com\/blog\/furnace-ignitor-replacement-signs-testing-and-diy\/","url":"https:\/\/modernhvactech.com\/blog\/furnace-ignitor-replacement-signs-testing-and-diy\/","name":"Furnace Ignitor Replacement: Signs, Testing, and DIY - Modern HVAC Tech","isPartOf":{"@id":"https:\/\/modernhvactech.com\/#website"},"primaryImageOfPage":{"@id":"https:\/\/modernhvactech.com\/blog\/furnace-ignitor-replacement-signs-testing-and-diy\/#primaryimage"},"image":{"@id":"https:\/\/modernhvactech.com\/blog\/furnace-ignitor-replacement-signs-testing-and-diy\/#primaryimage"},"thumbnailUrl":"https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/Ignitor.png","datePublished":"2026-11-17T16:48:29+00:00","description":"Furnace ignitor replacement guide: spot the signs, confirm the fault, compare and replace the part","breadcrumb":{"@id":"https:\/\/modernhvactech.com\/blog\/furnace-ignitor-replacement-signs-testing-and-diy\/#breadcrumb"},"inLanguage":"es","potentialAction":[{"@type":"ReadAction","target":["https:\/\/modernhvactech.com\/blog\/furnace-ignitor-replacement-signs-testing-and-diy\/"]}]},{"@type":"ImageObject","inLanguage":"es","@id":"https:\/\/modernhvactech.com\/blog\/furnace-ignitor-replacement-signs-testing-and-diy\/#primaryimage","url":"https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/Ignitor.png","contentUrl":"https:\/\/modernhvactech.com\/wp-content\/uploads\/2026\/11\/Ignitor.png"},{"@type":"BreadcrumbList","@id":"https:\/\/modernhvactech.com\/blog\/furnace-ignitor-replacement-signs-testing-and-diy\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/modernhvactech.com\/"},{"@type":"ListItem","position":2,"name":"Furnace Ignitor Replacement: Signs, Testing, and DIY"}]},{"@type":"WebSite","@id":"https:\/\/modernhvactech.com\/#website","url":"https:\/\/modernhvactech.com\/","name":"modernhvactech.com","description":"HVAC Company in Chicago","publisher":{"@id":"https:\/\/modernhvactech.com\/#organization"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/modernhvactech.com\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"es"},{"@type":"Organization","@id":"https:\/\/modernhvactech.com\/#organization","name":"Modern HVAC Technology LLC","url":"https:\/\/modernhvactech.com\/","logo":{"@type":"ImageObject","inLanguage":"es","@id":"https:\/\/modernhvactech.com\/#\/schema\/logo\/image\/","url":"https:\/\/modernhvactech.com\/wp-content\/uploads\/2023\/12\/logo-1.png","contentUrl":"https:\/\/modernhvactech.com\/wp-content\/uploads\/2023\/12\/logo-1.png","width":2485,"height":737,"caption":"Modern HVAC Technology LLC"},"image":{"@id":"https:\/\/modernhvactech.com\/#\/schema\/logo\/image\/"},"sameAs":["https:\/\/www.facebook.com\/modernhvactech\/","https:\/\/www.tiktok.com\/@modernhvactechnol"]},{"@type":"Person","@id":"https:\/\/modernhvactech.com\/#\/schema\/person\/06119bfaabf31ac6bb760868d84c5fc7","name":"administraci\u00f3n","sameAs":["https:\/\/modernhvactech.com"]}]}},"_links":{"self":[{"href":"https:\/\/modernhvactech.com\/es\/wp-json\/wp\/v2\/posts\/3649","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/modernhvactech.com\/es\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/modernhvactech.com\/es\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/modernhvactech.com\/es\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/modernhvactech.com\/es\/wp-json\/wp\/v2\/comments?post=3649"}],"version-history":[{"count":6,"href":"https:\/\/modernhvactech.com\/es\/wp-json\/wp\/v2\/posts\/3649\/revisions"}],"predecessor-version":[{"id":3658,"href":"https:\/\/modernhvactech.com\/es\/wp-json\/wp\/v2\/posts\/3649\/revisions\/3658"}],"wp:attachment":[{"href":"https:\/\/modernhvactech.com\/es\/wp-json\/wp\/v2\/media?parent=3649"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/modernhvactech.com\/es\/wp-json\/wp\/v2\/categories?post=3649"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/modernhvactech.com\/es\/wp-json\/wp\/v2\/tags?post=3649"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}